Taper Ties
Technical Product Data Sheet
Description
OCM INC. Taper Ties are used to connect gang modular forms and are a 100% reusable tie, and can be supplied with Coil Thread or Euro Thread as required. OCM Inc. Taper Ties are manufactured with a square end so they can be turned with a wrench and a protruding nose to protect the thread during use and installation. Safe Working load is based on a Safety Factor of 2:1.
INSTALLATION INSTRUCTIONS
1. Thread large wing nut and slide flat washer on to taper tie
2. Install taper tie into the formwork when both panels are set
3. After concrete is poured and gains strength, remove small wing nut and flat washer
4. Hit taper tie on small end and remove it
5. Coating the taper tie with waterproof grease will facilitate taper tie removal
Features
- Completely reusable.
| OCM Part No. | Large End of Tie | Small End of Tie | Standard Tie Length |
Tapered Body Diameter |
Safe Working Load lbs |
||
|---|---|---|---|---|---|---|---|
| Coil Thread Diameter |
Length of Thread |
Coil Thread Diameter |
Length of Thread |
||||
| 7550TT42P | 3/4" | 10" | 1/2" | 6" | 42" | .750" to .670" | 7,500 |
| 7550TT36P | 3/4" | 10" | 1/2" | 6" | 36" | .670" to .500" | 7,500 |
| 7550TT48P | 3/4" | 10" | 1/2" | 6" | 48" | .670" to .500" | 7,500 |
| 75100TT30P | 1" | 10" | 3/4" | 6" | 30" | .884" to .750" | 18,000 |
| 75100TT48P | 1" | 10" | 3/4" | 6" | 48" | .884" to .750" | 18,000 |
| 75100TT54P | 1" | 10" | 3/4" | 6" | 54" | .884" to .750" | 18,000 |
| 75100TT60P | 1" | 10" | 3/4" | 6" | 60" | .884" to .750" | 18,000 |
| 100125TT36P | 1-1/4" | 10" | 1" | 6" | 36" | .884" to .750" | 34,000 |
| 100125TT42P | 1-1/4" | 10" | 1" | 6" | 42" | 1.113" to 1.00" | 34,000 |
| 100125TT48P | 1-1/4" | 10" | 1" | 6" | 48" | 1.113" to 1.00" | 34,000 |
| 100125TT54P | 1-1/4" | 10" | 1" | 6" | 54" | 1.113" to 1.00" | 34,000 |
| 100125TT66P | 1-1/4" | 10" | 1" | 6" | 66" | 1.113" to 1.00" | 34,000 |
| 100125TT72P | 1-1/4" | 10" | 1" | 6" | 72" | 1.113" to 1.00" | 34,000 |
| 125100TT45P | 1-1/4" | 10" | 1" | 6" | 45" | 1.113" to 1.00" | 34,000 |
Comments: SWL provides a safety factor of approximately 2 to 1. *Additional lengths available upon request. Euro Thread Taper Ties available upon request.
OCM Limited Warranty
All recommendations, statements and technical data contained herein are based on tests we believe to be reliable and correct; however, accuracy and completeness of said tests are not guaranteed and are not provided as an express or implied warranty. User shall rely on his or her own information and tests to determine suitability of the product for the intended use and user assumes all risk and liability resulting from his or her use of the product. In the event that a product supplied by OCM, Inc. proves to not meet the OCM, Inc. published dimensional or other specifications of the product, an OCM, Inc. representative will review such product and circumstances to determine whether a replacement is warranted. OCM, Inc.'s and its manufacturer's sole responsibility shall be to replace, at OCM, Inc.'s sole discretion that product or portion of the product which OCM, Inc. deems to be defective, within six months of the delivery of the product. OCM, Inc. disclaims all other warranties or conditions, whether express or implied, including an implied warranties of merchantability or fitness for any particular purpose. In no event shall OCM, Inc. or its parent or affiliated companies be liable for delay caused by defects, for loss of use, or for any indirect, incidental, special, or consequential damages or for any charges or expenses of any nature whatsoever. In no event shall OCM, Inc.'s liability exceed the purchase price paid for the particular affect OCM, Inc. products.